Direct answer: a U.S. upholstered furniture flammability submittal should identify the in-scope finished products, map every cover, filling, barrier and decking material to the applicable TB 117-2013 evidence, show the compliant construction route, approve the permanent 16 CFR part 1640 label, and freeze those components in the bill of materials. A supplier statement saying “TB117 foam” or one unrelated fabric report does not establish compliance for every sofa, chair and upholstery option in an order.

This guide is for U.S. importers, furniture brands, hospitality buyers and sourcing teams approving upholstered seating made in China. It explains how to organize the evidence before purchase and production. It is not legal advice, and product scope should be confirmed against the current regulation and CPSC guidance.

Start with product scope, not the test report

The U.S. Consumer Product Safety Commission states that 16 CFR part 1640 applies to covered upholstered furniture manufactured, imported or reupholstered on or after June 25, 2021. The permanent certification-label requirement applies to covered products manufactured, imported or reupholstered on or after June 25, 2022. The rule incorporates the smolder-resistance methods in California Technical Bulletin 117-2013.

Scope review must be model-specific. Seating furniture is not automatically covered merely because it contains fabric, and a product is not automatically exempt because it is sold for a project. Record the product type, intended use, construction, filling thickness and destination. Sofa beds need special attention: the CPSC explains that a detachable mattress is generally addressed under the mattress rules, while the remaining seating product may fall under part 1640.

Buyer decision: create a scope register before requesting tests. Include every model, size and upholstery option, and record whether it is in scope, excluded or needs specialist confirmation. Keep the reason and source for each decision.

Build a component-to-evidence matrix

TB 117-2013 contains separate methods for cover fabrics, barrier materials, resilient filling materials and decking materials. The CPSC describes two basic compliance routes for the upholstery construction: a passing barrier that surrounds the filling, or a passing cover fabric together with passing filling material. Decking, when present, must pass its applicable test.

Controlled itemWhat the submittal should identifyEvidence checkProduction control
Outer coverSupplier, article number, colorway, fiber or material description, finish and backingReport identifies the tested cover material and TB 117-2013 sectionRoll and dye-lot traceability; no unapproved backing or finish change
Resilient fillingFoam grade, density or product code, thickness range, supplier and locationTest specimen matches the released filling or the construction uses an approved passing barrier routeIncoming labels, cut-part identity and substitution lock
Barrier or interlinerMaterial code, weight or construction, coverage and seam treatmentPassing barrier report and installation detail match the compliance routeCut pattern and in-process inspection confirm required coverage
Batting and loose fillFiber type, weight, supplier, location and relationship to barrierClassified correctly within the tested constructionMaterial labels and controlled assembly sequence
DeckingArticle number, composition, coating or backing and exposed locationApplicable decking test resultCorrect material used below cushions and in concealed zones
Finished modelModel, SKU, size, reversible or non-reversible cushions, component map and optionsEvery component is linked to a valid compliance routeFrozen BOM, approved sample and change-control record
Permanent labelExact statement, dimensions, language, location and attachment methodArtwork matches 16 CFR 1640.4 and current CPSC guidanceFirst-article inspection and final random check

The material identity in the matrix should use the same codes as the purchase order, factory BOM, approved samples and inspection checklist. The upholstery fabric test-plan guide explains how to keep report samples, colorways and production rolls aligned.

Understand what the report does and does not prove

A useful report names the laboratory, test method and edition, report date, specimen identity, conditioning, test section, results and conclusion. It should include enough photographs or descriptions to distinguish the tested material from visually similar alternatives. Review whether the report belongs to the actual supplier and article number offered for the order.

Do not treat “pass” as a transferable property of a material family. A new coating, backing, fiber blend, foam formulation or barrier construction can affect identity and performance. Ask the laboratory or qualified compliance adviser whether the proposed variation is covered. If evidence cannot be mapped to the production material, test the intended construction rather than relying on a guess.

TB 117-2013 is a smolder-resistance component standard. It does not by itself establish compliance with every contract, building, chemical, accessibility or product-safety requirement. A hotel specification may call for additional fire-performance evidence, but that requirement should be reviewed separately instead of being presented as part 1640.

Choose and document the compliance route

Passing cover plus passing filling

This route can be straightforward when both materials have matching evidence. The submittal should still identify batting, decking and any backing or treatment. If multiple fabrics are offered, every option needs a documented route; one passing base fabric does not release an entire color and material library.

Passing barrier route

CPSC guidance says a qualifying barrier can support compliance when cover fabric or resilient filling does not pass its own section, subject to the TB 117-2013 construction requirements. The barrier must be installed as required around the filling, including the applicable cushion surfaces and permitted exceptions. The submittal therefore needs a cut-and-sew detail, seam locations and inspection access, not just the barrier test report.

Review the real sofa or chair geometry. Zippers, tufting, buttons, pull points, vents and attached cushions can interrupt coverage. Approve the construction in a representative prototype and record the barrier before the upholstery closes it. Our sofa comfort specification guide can be used alongside this review so compliance changes do not silently alter cushion feel.

Freeze evidence at SKU and option level

One model can have several upholstery covers, foam combinations and cushion constructions. Build a configuration table with one row per released combination. Where a common construction is used across several models, state the controlled boundaries: component codes, thicknesses, barrier coverage and manufacturing site.

For project orders, link the room schedule and furniture code to the released configuration. The factory should not substitute foam because a preferred grade is unavailable or replace a barrier with a similar-weight nonwoven. Use written engineering change control and repeat the evidence review before accepting any material change.

Release hold point: production may start only when the compliance matrix, BOM, material approvals, prototype construction and label artwork show the same component codes and revision.

Approve the permanent label correctly

The CPSC FAQ states that covered upholstered furniture must carry the permanent statement “Complies with U.S. CPSC requirements for upholstered furniture flammability.” The statement must be in English on the front of the label. CPSC staff recommends conspicuous, legible presentation, at least 1/8 inch high, not smaller than other label text, with black text on a white background surrounded by a black border.

A hangtag or zip tie is not considered permanent. Approve the label material, print durability, location and attachment method, then inspect it on the first article and packed product. The federal statement does not replace other labels required by law, including California disclosure labeling where applicable.

CPSC guidance also says a General Certificate of Conformity is not required solely for part 1640; the permanent certification label is the required certification mechanism. Other applicable rules can create separate testing or certificate obligations, so do not use that point to waive a wider product-compliance review.

Control supplier and laboratory records

Obtain the complete report rather than a cropped cover page. Verify the issuing laboratory, report number and material identification. Keep supplier declarations, purchase specifications, invoices, lot labels, approved samples and BOM revisions together with the test evidence. CPSC recommends maintaining records for at least as long as the product remains in production.

For fabric, preserve a sealed cutting and the supplier label. For foam, retain the grade and batch information that links delivered blocks or sheets to the approved source. The furniture foam sourcing guide covers density, hardness, recovery and lot controls that remain important beyond flammability.

Inspect the construction before it disappears

  1. Incoming materials: compare supplier, article code, batch or roll, color and package labels with the approved register.
  2. Cutting: control mixed rolls, backing orientation and barrier patterns; segregate rejected or unidentified material.
  3. First assembly: photograph cover, filling, decking and barrier placement before closure. Confirm seams and openings match the approved construction.
  4. In-process checks: sample component codes and barrier coverage at the upholstery line, especially after style changeovers.
  5. Final inspection: confirm model and upholstery option, permanent label, traceability and packing identity.

Combine these checks with the furniture quality control plan. Flammability evidence does not replace frame, seam, comfort, stability, finish or packaging inspection.

Common rejection reasons

ProblemWhy approval should stopCorrective action
Report uses only a trade nameThe production article and tested specimen cannot be matchedObtain full identification or test the intended material
One fabric report is applied to all optionsDifferent articles, finishes or backings may not be coveredMap evidence separately for each released option
Barrier report has no construction detailPassing material does not prove correct coverage in the furnitureApprove a cut-and-sew barrier drawing and inspect the prototype
Factory changes foam gradeThe released compliance route and comfort specification may changeStop substitution, reassess evidence and update the BOM
Certification appears on a hangtagThe required certification label must be permanentApprove a securely attached permanent label
“TB117” is treated as all fire complianceProject and market requirements may be broader and differentCreate a separate destination and contract compliance matrix

Submittal checklist for importers

  • Define product scope and document exclusions or uncertain cases.
  • List every model, cover option, filling, barrier and decking component.
  • Map each production code to a complete, relevant TB 117-2013 report.
  • State the compliant construction route and barrier coverage where used.
  • Freeze the evidence matrix into the BOM and approved prototype.
  • Approve permanent label artwork, location and attachment.
  • Inspect component identity and concealed construction during production.
  • Keep evidence and revision records while the product remains in production.

Primary sources

The strongest submittal is a traceability system, not a folder of PDFs. It lets the importer show which rule applies, which construction passes, which materials were purchased and whether the factory built the released version.