A restaurant booth order should not be released from a reference photo alone. The buyer needs a coordinated booth-and-table drawing, a material schedule, a signed production sample and measurable acceptance rules for dimensions, comfort, structure, upholstery, fixing and installation. Fixed seating is difficult to correct after delivery, so the cheapest place to resolve a conflict is on the shop drawing.

Booth upholstery should not be approved from a high abrasion headline alone. Use the contract upholstery fabric testing workflow to match methods to traffic, cleaning, seams and light exposure, then connect laboratory evidence to the finished sample and bulk rolls.

This guide is for restaurant groups, hospitality contractors and import buyers sourcing banquettes or booths from China. It focuses on the information a supplier needs to quote the same product the project expects, and on the evidence a buyer should retain before approving mass production.

Start with the room, not a catalog model

A booth is part furniture and part fit-out. Its usable depth depends on the wall, skirting, upholstery build-up, table position and seated clearance. Its length may need scribes or removable end panels to absorb site variation. Before requesting a quotation, issue a measured plan that identifies finished wall faces, floor level changes, columns, sockets, vents, service panels and the intended table centerline.

Give every booth type a stable reference such as B01, B02 and B03. Use that reference on the floor plan, elevation, bill of quantities, production drawing, carton label and installation plan. The same identification discipline is useful across a broader restaurant furniture procurement package.

RFQ fieldWhat to defineRelease evidence
ConfigurationWall banquette, single booth, back-to-back booth, curved booth or freestanding unitPlan and elevation with booth reference
GeometryFinished length, seat height, usable seat depth, back angle, back height, plinth and table relationshipDimensioned shop drawing plus full-size section
ConstructionFrame, structural panels, suspension, foam layers, edge radii, access panels and fixing pointsSection drawing, bill of materials and prototype
UpholsteryExact textile, roll direction, seam layout, piping, stitch, pattern placement and cleanabilityTagged control sample and approved seam panel
InterfacesWall substrate, floor, table base, power, ventilation, service access and adjacent finishesResponsibility matrix and fixing detail
DeliveryModule size, site access, assembly joints, protection, room coding and installation sequencePacking drawing and installation method statement

Approve the booth and table as one seating system

Seat dimensions that feel acceptable in isolation may fail when paired with the specified table. Build or mock up one complete bay with the production seat profile, table thickness and base. Check entry, seated posture, knee clearance, table reach and the space available for cleaning. For a two-sided booth, verify the full face-to-face footprint rather than approving one bench against a wall.

Do not copy a supplier’s “standard” dimensions without testing the intended guests and service model. A quick-service venue, fine-dining restaurant and laptop-friendly café may need different table positions, back profiles and dwell-time comfort. Record the agreed dimensions from finished floor and finished upholstery surfaces; foam compression should not be confused with the unloaded construction dimension.

Accessibility is a project requirement, not an optional furniture feature. Under the U.S. Access Board’s ADA scoping provisions for dining surfaces, at least 5 percent of seating and standing spaces at dining surfaces must comply and be dispersed where required. The technical provisions in Section 902 address clear floor space, knee and toe clearance, and a dining-surface height of 28 to 34 inches. The project designer should identify the compliant locations on the plan; a fixed booth that blocks the required approach cannot be corrected by changing upholstery.

Specify construction in layers

“Commercial grade” is not a construction specification. Ask the factory to identify the load path from the occupant through the seat deck, frame, plinth and fixings. For timber or panel frames, define material type, section or thickness, joint method, reinforcement and moisture condition. For metal frames, identify alloy or steel grade where material performance matters, tube dimensions, weld finishing, coating and isolation between dissimilar metals.

For upholstered components, list the suspension, individual foam layers, nominal density or other agreed identification, thickness and firmness target. Density and firmness describe different properties; one cannot substitute for the other. Retain a signed cushion or cut section because these materials become invisible after upholstery.

If regulated composite wood is used in products destined for the United States, confirm whether the materials and finished goods fall within the EPA’s TSCA Title VI composite wood requirements. Generic claims such as “E0 board” do not replace destination-specific documentation.

Turn appearance into an inspection rule

Appearance problems often come from uncontrolled decisions rather than obvious workmanship defects. The buyer should approve how a pattern runs across modules, where vertical seams fall, how piping meets corners, how the plinth aligns with wall panels and what variation is acceptable between adjacent pieces. View the sample under lighting similar to the restaurant, including low-angle light that reveals puckering, ripples and inconsistent top stitching.

  • Label the master upholstery, finish and thread samples with supplier, code, color and approval date.
  • Define whether textile from different dye lots may appear in one continuous booth run.
  • Mark the front face, roll direction and pattern centerline for directional textiles.
  • Approve a repair standard for small marks; do not let the factory invent one during final inspection.
  • Record visible faces and normal viewing distance instead of demanding an undefined “perfect finish.”

Related movable seating should follow the same controlled finish family. The guide to wholesale dining-chair construction and QC explains the additional frame, joint and stability controls for chairs.

Select tests from the destination and construction

The contract should name the applicable test method, edition, configuration and acceptance level. A test report for another fabric, foam stack, frame size or component combination may not represent the ordered booth. For U.S. projects subject to California upholstered-furniture rules, the California Bureau of Household Goods and Services publishes the official TB 117-2013 materials and regulatory documents. Confirm scope and labeling obligations with a qualified adviser for the exact product and market.

Structural and durability testing should also reflect how the booth is supported. A wall-fixed banquette, freestanding booth and modular back-to-back unit do not transfer loads in the same way. The sample used for testing should use production fasteners, substrate assumptions and joint details. Keep the report, specimen description and photographs together so procurement can see what was actually evaluated.

Use a production release gate

GateBuyer checkDo not release when
DrawingAll dimensions, modules, scribes, joints, table positions and fixings are coordinatedSite dimensions or interface responsibilities remain blank
MaterialVisible and concealed materials match the controlled bill of materialsPrototype substitutions are not identified
Full bayComfort, entry, clearance, table relationship and cleaning access are acceptedOnly a loose cushion or miniature sample was reviewed
EvidenceRequired test and compliance documents identify the purchased configurationReports cannot be matched to materials or model
InstallationAccess, module split, fixing substrate, protection and room coding are definedThe finished unit cannot pass through the delivery route

Inspect what production can change

At first article, compare the unit with the signed sample and latest drawing before the batch advances. During production, check frame dimensions, joint execution, reinforcement, fixing inserts, foam identification, textile orientation and seam location while they are still visible. Final inspection should sample across booth types and production periods rather than selecting only the easiest units near the warehouse door.

  1. Confirm booth code, drawing revision, quantity and module sequence.
  2. Measure agreed control dimensions from finished surfaces.
  3. Operate removable panels and verify access to fasteners or services.
  4. Check level, rocking, sharp edges, exposed staples, noise and loose trim.
  5. Compare color, texture, seam position and workmanship with signed controls.
  6. Trial-assemble one representative run with its table and production connectors.
  7. Verify carton labels, hardware kits, wall scribes, installation drawings and spare material.

Large upholstery is vulnerable to rubbing, crushing and contamination in transit. Build the route and handling method into the furniture packaging test plan; a clean sample-room booth is not proof that the export package protects projecting corners and finished faces.

Issue one controlled handover package

The final handover should contain the floor plan, booth schedule, approved shop drawings, bill of materials, finish controls, test evidence, inspection criteria, packing drawings, installation method and spare-parts list. Mark superseded revisions. The wholesale restaurant furniture guide can help coordinate the booths with tables, chairs and other venue furniture, while a structured furniture RFQ keeps supplier quotations comparable.

The practical rule is simple: approve a buildable seating system, not an attractive photograph. When the drawing, sample, evidence and inspection plan describe the same booth, the factory has a repeatable target and the buyer has a defensible release decision.